Keysight DSOX3012T Скачать руководство пользователя страница 262

Страница: 262 / 530

262

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Measurements

•

Source 1

Source 2

— waveform source.

•

Source 1 Slope

Source 2 Slope

— rising edge or falling edge.

•

Source 1 Edge #

Source 2 Edge #

— edge number for the selected source.

When

Auto

is selected for the

Source 1 Edge #

, the edge closest to the

timebase reference point is used.

Auto

is also automatically selected for the

Source 2 Edge #

, and cannot be changed. In this case, the source 2 edge

closest to the source 1 edge is used.

When edge numbers are selected, edges are counted from the left side of

the display for both sources.

Press the

Add Measurement

softkey to make the measurement.

The example below shows a delay measurement between the rising edge of

channel 1 and the rising edge of channel 2.

Phase

Phase is the calculated phase shift from source 1 to source 2, expressed in

degrees. Negative phase shift values indicate that the rising edge of source 1

occurred after the rising edge of source 2.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды