Keysight DSOX3012T Скачать руководство пользователя страница 27

Страница: 27 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

1 Getting Started

Inspect the Package Contents / 27
Tilt the Oscilloscope for Easy Viewing / 30
Power-On the Oscilloscope / 31
Connect Probes to the Oscilloscope / 32
Input a Waveform / 33
Recall the Default Oscilloscope Setup / 33
Use Autoscale / 34
Compensate Passive Probes / 36
Learn the Front Panel Controls and Connectors / 37
Learn the Touchscreen Controls / 45
Learn the Rear Panel Connectors / 58
Learn the Oscilloscope Display / 59
Access the Built-In Quick Help / 61

This chapter describes the steps you take when using the oscilloscope for the first

time.

Inspect the Package Contents

• Inspect the shipping container for damage.

If your shipping container appears to be damaged, keep the shipping container

or cushioning material until you have inspected the contents of the shipment

for completeness and have checked the oscilloscope mechanically and

electrically.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды