Keysight DSOX3012T Скачать руководство пользователя страница 30

Страница: 30 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Getting Started

Install the Optional LAN/VGA or GPIB Module

If you need to install a DSOXLAN LAN/VGA module or a DSOXGPIB GPIB module,

perform this installation before you power on the oscilloscope.

If you need to remove a module before installing a different module, pinch the

module's spring tabs, and gently remove the module from the slot.

To install a module, slide the module into the slot on the back until it is fully

seated.

The module's spring tabs will latch into the slot, keeping the module in place.

Tilt the Oscilloscope for Easy Viewing

There are tabs under the oscilloscope's front feet that can be flipped out to tilt the

oscilloscope.

100 Watts MAX

100-240V, 50/60Hz

100-120V, 50/60/400Hz

WARNING: MAIN TAIN
GROUND TO AVOID
ELECTRIC SHOCK

LAN/VGA Module

GPIB Module

Module Slot

NOTE

The LAN/VGA or GPIB module must be installed before powering on the oscilloscope.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды