Keysight DSOX3012T Скачать руководство пользователя страница 184

Страница: 184 / 530

184

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Triggers

The NFC trigger type is license-enabled. The license also enables companion

PC-based automated test software.

When the NFC trigger type is selected, there are softkeys for selecting the source,

signaling technology standard, trigger event, and other settings:

Press the

[Trigger]

key.

In the Trigger Menu, press the

Trigger

softkey; then, turn the Entry knob to

select

Near Field Communication (NFC)

Table 3

NFC Triggering Characteristics

Standard:

Trigger on:

In "Arm & Trigger":

Arm on:

Trigger on:

NFC-A

•

SENS_REQ

•

ALL_REQ

•

Either (SENS_REQ or

ALL_REQ)

•

SDD_REQ

•

Arm & Trigger

•

SENS_REQ

•

ALL_REQ

•

Either (SENS_REQ or

ALL_REQ)

•

SDD_REQ or Timeout

NFC-B

•

SENSB_REQ

•

ALLB_REQ

•

Either (SENSB_REQ or

ALLB_REQ)

•

ATTRIB

•

Arm & Trigger

•

SENSB_REQ

•

ALLB_REQ

•

Either (SENB_REQ or

ALLB_REQ)

•

ATTRIB or Timeout

NFC-F

•

SENSF_REQ

•

ATR_REQ

•

Preamble

•

Arm & Trigger

•

SENSF_REQ

•

ATR_REQ or Timeout

Notes:

When using the

Arm & Trigger

selection, the oscilloscope arms on one event and then triggers on a second event or after a

specified timeout period if the second event does not occur

Both NFC-F (212 kbps) and NFC-F (424 kbps) are supported.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды