Keysight DSOX3012T Скачать руководство пользователя страница 138

Страница: 138 / 530

138

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Digital Channels

The sizing control lets you spread out or compress the digital traces vertically on

the display for more convenient viewing.

To switch a single channel on or off

With the Digital Channel Menu displayed, rotate the Entry knob to select the

desired channel from the popup menu.

Push the Entry knob or press the softkey that is directly below the popup menu

to switch the selected channel on or off.

To switch all digital channels on or off

Press the

[Digital]

key to toggle the display of digital channels. The Digital

Channel Menu is displayed above the softkeys.

If you want to switch the digital channels off, and the Digital Channel Menu is not

already displayed, you must push the

[Digital]

key twice to switch the digital

channels off. The first push displays the Digital Channel Menu, and the second

push switches the channels off.

To switch groups of channels on or off

Press the

[Digital]

key on the front panel if the Digital Channel Menu is not

already displayed.

Press the

Turn off

(or

Turn on

) softkey for the

D15 - D8

group or the

D7 - D0

group.

Each time you press the softkey, the softkey's mode toggles between

Turn on

and

Turn off

To change the logic threshold for digital channels

Press the

[Digital]

key so that the Digital Channel Menu is displayed.

Press the

Thresholds

softkey

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды