Keysight DSOX3012T Скачать руководство пользователя страница 87

Страница: 87 / 530

Vertical Controls

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Press the Channel on/off key to turn the channel on (if the channel is off).

In the Channel Menu, press the

Probe

softkey.

In the Channel Probe Menu, the second softkey from the left is for specifying

your probe head (and attenuation). Repeatedly press this softkey until the

probe head selection matches the attenuator you are using.

The choices are:

•

10:1 single-ended browser (no attenuator).

•

10:1 differential browser (no attenuator).

•

10:1 (+6 dB Atten) single-ended browser.

•

10:1 (+6 dB Atten) differential browser.

•

10:1 (+12 dB Atten) single-ended browser.

•

10:1 (+12 dB Atten) differential browser.

•

10:1 (+20 dB Atten) single-ended browser.

•

10:1 (+20 dB Atten) differential browser.

Press the

Calibrate Probe

softkey and follow the instructions on the display.

For more information on InfiniiMax probes and accessories, see the probe's

User's

Guide

NOTE

When calibrating a differential probe, connect the positive lead to the Probe Comp terminal

and the negative lead to the ground terminal. You may need to connect an alligator clip to the

ground lug to allow a differential probe to span between the Probe Comp test point and

ground. A good ground connection ensures the most accurate probe calibration.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды