Keysight DSOX3012T Скачать руководство пользователя страница 405

Страница: 405 / 530

CAN/LIN Triggering and Serial Decode

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

405

• A partial frame occurs when the oscilloscope detects any error condition during

a frame that is not followed by an active error flag. Partial frames are not

counted.

Counters

• The FRAMES counter gives the total number of completed remote, data,

overload, and active error frames.

• The SPEC counter gives the total number of Specification errors. This counter

tracks the number of Acknowledge, Form, Stuff, and CRC errors. If a packet has

more than one type of error, that packet will increment the counter by the total

number of errors in the packet.

• The ERR FR counter gives the total number of completed active error frames

and their percentage of the total number of frames.

• The LOAD (bus load) indicator measures the percentage of time the bus is

active. The calculation is done on 330 ms periods, approximately every 400 ms.

Example: If a data frame contains an active error flag, both the FRAMES counter

and the ERR FR counter will be incremented. If a data frame contains an error that

is not an active error it is considered a partial frame and no counters are

incremented.

Interpreting CAN Lister Data

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды