Keysight DSOX3012T Скачать руководство пользователя страница 92

Страница: 92 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

FFT Spectral Analysis

You can make peak-to-peak, maximum, minimum, and average dB

measurements on the FFT waveform. You can also find the frequency value at

the first occurrence of the waveform maximum by using the X at Max Y

measurement.

To adjust the FFT waveform scale and offset

Make sure the multiplexed scale and position knobs above and below the

[FFT]

key are selected for the FFT waveform.

If the arrow to the left of the

[FFT]

key is not illuminated, press the key.

Use the multiplexed scale and position knobs next to the

[Math]

key to re-size

and re-position the math waveform.

The following FFT spectrum was obtained by connecting a 2.5 V, 100 kHz square

wave to channel 4. Set the horizontal scale to 50 µs/div, vertical sensitivity to

1 V/div, Units/div to 20 dBV, Offset to -40.0 dBV, Center frequency to 500 kHz,

frequency Span to 1 MHz, and window to Hanning.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды