manualshive.com logo in svg

Keysight DSOX3012T, Руководство пользователя

Keysight DSOX3012T - мощный осциллограф с функциональностью отличного качества. Пользовательская инструкция доступна для бесплатного скачивания на manualshive.com. Используйте этот ресурс для получения подробной информации о продукте и его функциях. Идеальный инструмент для профессиональных и любительских проектов.

Поделиться
Скачать
background image

I2C/SPI Triggering and Serial Decode

28

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

441

 

5

If you have set the oscilloscope to trigger on an EEPROM Data Read condition:

Press the 

Data is

 softkey to set the oscilloscope to trigger when data is = (equal 

to), 

≠

(not equal to), < (less than), or > (greater than) the data value set in the 

Data

 softkey.

The oscilloscope will trigger on the clock edge for the Ack bit after the trigger 

event is found. This data byte does not need to occur directly after the control 

byte. The oscilloscope will trigger on any data byte that meets the criteria 

defined by the 

Data is

 and 

Data

 softkeys during a current address read or a 

random read or a sequential read cycle.

6

If you have set the oscilloscope to trigger on a 7-bit address read or write frame 

condition or a 10-bit write frame condition:

a

Press the 

Address

 softkey and turn the Entry knob to select the 7-bit or 

10-bit device address.

You can select from an address range of 0x00 to 0x7F (7-bit) or 0x3FF 

(10-bit) hexadecimal. When triggering on a read/write frame, the 

oscilloscope will trigger after the start, address, read/write, acknowledge, 

and data events occur.

If don't care is selected (0xXX or 0xXXX) for the address, the address will be 

ignored. The trigger will always occur on the 17th clock for 7-bit addressing 

or 26th clock for 10-bit addressing.

b

Press the 

Data

 value softkey and turn the Entry knob to select the 8-bit data 

pattern on which to trigger.

You can select a data value in the range of 0x00 to 0xFF (hexadecimal). The 

oscilloscope will trigger after the start, address, read/write, acknowledge, 

and data events occur.

If don't care (0xXX) is selected for data, the data will be ignored. The trigger 

will always occur on the 17th clock for 7-bit addressing or 26th clock for 

10-bit addressing.

c

If you have selected a three-byte trigger, press the 

Data2

 value softkey and 

turn the Entry knob to select the 8-bit data pattern on which to trigger.

NOTE

To display I2C serial decode, see 

“I2C Serial Decode"

on page 442.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSOX3012T

Makerfire N10 Instructions Manual preview
N10
Бренд: Makerfire Страницы: 10
Navman 2 Installation And Operation Manual preview
2
Бренд: Navman Страницы: 17
YardCraft Polaris Assembly Manual preview
Polaris
Бренд: YardCraft Страницы: 17
Obdstar BT06 Instructions For Functions preview
BT06
Бренд: Obdstar Страницы: 10
QBC Diagnostics Star Operators & Service Manual preview
Star
Бренд: QBC Diagnostics Страницы: 65
M-Audio X-Session Pro User Manual preview
X-Session Pro
Бренд: M-Audio Страницы: 12
M-Audio USB OMNISTUDIO Manual Del Usuario preview
USB OMNISTUDIO
Бренд: M-Audio Страницы: 64
M-Audio Pro Tools User Manual preview
Pro Tools
Бренд: M-Audio Страницы: 16
M-Audio ProjectMix I/O Quick Start Manual preview
ProjectMix I/O
Бренд: M-Audio Страницы: 4
M-Audio Delta 1010 Manual preview
Delta 1010
Бренд: M-Audio Страницы: 52
MacDon FlexDraper FD2 Series Quick Start Manual preview
FlexDraper FD2 Series
Бренд: MacDon Страницы: 2
M-Audio OXYGEN PRO MINI Quick Start Manual preview
OXYGEN PRO MINI
Бренд: M-Audio Страницы: 56
Ofa Bamberg memory Instructions For Use Manual preview
memory
Бренд: Ofa Bamberg Страницы: 80
Safety 1st HS129 Manual preview
HS129
Бренд: Safety 1st Страницы: 4
Safety Engineering SELF BELAY Installation Manual preview
SELF BELAY
Бренд: Safety Engineering Страницы: 5
MAGSTIM NEUROSIGN V4 User Manual preview
NEUROSIGN V4
Бренд: MAGSTIM Страницы: 86
SHOWTEC LED PowerBank 48 Product Manual preview
LED PowerBank 48
Бренд: SHOWTEC Страницы: 12
Erbe VIO 3 Manual preview
VIO 3
Бренд: Erbe Страницы: 124

Бренды по названию

Популярные бренды

Загрузить еще бренды