manualshive.com logo in svg

Keysight DSOX3012T, Руководство пользователя

Keysight DSOX3012T - мощный осциллограф с функциональностью отличного качества. Пользовательская инструкция доступна для бесплатного скачивания на manualshive.com. Используйте этот ресурс для получения подробной информации о продукте и его функциях. Идеальный инструмент для профессиональных и любительских проектов.

Поделиться
Скачать
background image

344

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

22

Utility Settings

 

5

Configure the oscilloscope's LAN interface:

a

Use the 

Modify

 softkey (and the other softkeys and keypad entry dialogs) to 

enter the IP Address, Subnet Mask, Gateway IP, and DNS IP values.

b

Press the 

Host name

 softkey and use the keypad entry dialog to enter the 

Host Name.

c

Press the 

Apply

 softkey.

6

Connect the oscilloscope to the local area network (LAN) by inserting the LAN 

cable into the "LAN" port on the rear panel of the oscilloscope.

Stand-alone (Point-to-Point) Connection to a PC

The following procedure describes how to establish a point-to-point (stand alone) 

connection to the oscilloscope. This is useful if you want to control the 

oscilloscope using a laptop computer or a stand-alone computer.

1

Press 

[Utility] > I/O

.

2

Press the 

LAN Settings

 softkey.

3

Press the 

Config

 softkey; then, turn the Entry knob to select 

Automatic

, and press 

the softkey again to enable it.

If your network supports DHCP or AutoIP, enabling 

Automatic

 lets the 

oscilloscope use those services to get its LAN configuration settings

4

Connect your PC to the oscilloscope using a cross-over LAN cable such as 

Keysight part number 5061-0701, available on the web at 

www.keysight.com/find/parts

.

5

Cycle power on the oscilloscope. Wait until the LAN connection is configured:

•

Press 

[Utility] > I/O

 and wait until the LAN status shows "configured".

This may take a few minutes.

Now, the instrument is connected, and the instrument's web interface or remote 

control via LAN may be used.

File Explorer

The File Explorer lets you navigate the oscilloscope's internal file system and the 

file systems of connected USB storage devices.

From the internal file system, you can load oscilloscope setup files or mask files.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSOX3012T

ABI Attachments Infield Rascal Pro Setup Manual preview
Infield Rascal Pro
Бренд: ABI Attachments Страницы: 8
Abicor Binzel BRS-LC Operating Instruction preview
BRS-LC
Бренд: Abicor Binzel Страницы: 84
ABI Attachments ABI Force Z-23 Product Instruction Sheet preview
ABI Force Z-23
Бренд: ABI Attachments Страницы: 5
abem Terrameter LS User Manual preview
Terrameter LS
Бренд: abem Страницы: 47
Abely LiftMeUp Frequently Asked Questions preview
LiftMeUp
Бренд: Abely Страницы: 5
PANDROL CD100 User And Maintenance Manual preview
CD100
Бренд: PANDROL Страницы: 36
Badger Basket CABANA Assembly Instructions Manual preview
CABANA
Бренд: Badger Basket Страницы: 7
Backyard Discovery ASPEN 6515 Owner'S Manual preview
ASPEN 6515
Бренд: Backyard Discovery Страницы: 53
Federal Signal Corporation GH1 Instruction Sheet preview
GH1
Бренд: Federal Signal Corporation Страницы: 4
FEBER MEGA 4 IN LINE Quick Start Manual preview
MEGA 4 IN LINE
Бренд: FEBER Страницы: 2
FASTERHOLT FM4400 User Manual & Spare Parts Catalogue preview
FM4400
Бренд: FASTERHOLT Страницы: 96
h/p/cosmos 190/65 3p Original Instruction preview
190/65 3p
Бренд: h/p/cosmos Страницы: 81
Jeio tech Lab companion SI-300 Operating Instruction preview
Lab companion SI-300
Бренд: Jeio tech Страницы: 69
JDS Uniphase IP Video Test Option HST-3000 Product Manual preview
IP Video Test Option HST-3000
Бренд: JDS Uniphase Страницы: 4
Jct JH Series Operating Manual preview
JH Series
Бренд: Jct Страницы: 16
Native Instruments TRAKTOR KONTROL S4 User Manual preview
TRAKTOR KONTROL S4
Бренд: Native Instruments Страницы: 86
Native Instruments Maschine Reference Manual preview
Maschine
Бренд: Native Instruments Страницы: 245
Vatech Smart Plus PHT-35LHS Technical Manual preview
Smart Plus PHT-35LHS
Бренд: Vatech Страницы: 190

Бренды по названию

Популярные бренды

Загрузить еще бренды