Keysight DSOX3012T Скачать руководство пользователя страница 357

Страница: 357 / 530

Utility Settings

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

357

Enter your product's model number and serial number. The system will search

for the warranty status of your product and display the results. If the system

cannot find your product's warranty status, select

Contact Us

and speak with a

Keysight Technologies representative.

To contact Keysight

Information on contacting Keysight Technologies can be found at:

www.keysight.com/find/contactus

To return the instrument

Before shipping the oscilloscope to Keysight Technologies, contact your nearest

Keysight Technologies sales or service office for additional details. Information on

contacting Keysight Technologies can be found at:

www.keysight.com/find/contactus

Write the following information on a tag and attach it to the oscilloscope.

•

Name and address of owner.

•

Model number.

•

Serial number.

•

Description of service required or failure indication.

Remove accessories from the oscilloscope.

Only return accessories to Keysight Technologies if they are associated with the

failure symptoms.

Package the oscilloscope.

You can use the original shipping container, or provide your own materials

sufficient to protect the instrument during shipping.

Seal the shipping container securely, and mark it FRAGILE.

Configuring the [Quick Action] Key

The

[Quick Action]

key lets you perform common, repetitive actions by pressing a

single key.

To configure the

[Quick Action]

key:

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды