INVT Goodrive100 Series Скачать руководство пользователя страница 55

Страница: 55 / 192

Goodrive100 inverters

Keypad operation procedure

IKR Aandrijven en Besturen

www.ikr-industries.nl

Function

code

Name

Detailed instruction of parameters

Default

value

Modify

1: The terminal running command is valid when powering on.

If the running command is detected to be valid during

powering on, the system will start the inverter automatically

after the initialization.

Note:

this function should be selected with cautions, or

serious result may follow.

P01.19

The running

frequency is

lower than the

lower limit one

(valid if the

lower limit

frequency is

above 0)

This function code determines the running state of the

inverter when the set frequency is lower than the lower-limit

one.

0: Run at the lower-limit frequency

1: Stop

2: Hibernation

The inverter will coast to stop when the set frequency is lower

than the lower-limit one.if the set frequency is above the

lower limit one again and it lasts for the time set by P01.20,

the inverter will come back to the running state automatically.

◎

P01.20

Hibernation

restore delay

time

This function code determines the Hibernation delay time.

When the running frequency of the inverter is lower than the

lower limit one, the inverter will pause to stand by.

When the set frequency is above the lower limit one again

and it lasts for the time set by P01.20, the inverter will run

automatically.

Note:

The time is the total value when the set frequency is

0.0s

○

Содержание Goodrive100 Series

































































































































































































Результаты поиска

Содержание Goodrive100 Series

Отзывы:

Похожие инструкции для Goodrive100 Series

Бренды по названию

Популярные бренды

INVT Goodrive100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Goodrive100 Series

Отзывы:

Похожие инструкции для Goodrive100 Series

Бренды по названию

Популярные бренды