INVT Goodrive100 Series Скачать руководство пользователя страница 37

Страница: 37 / 192

Goodrive100 inverters

Keypad operation procedure

IKR Aandrijven en Besturen

www.ikr-industries.nl

4.1 Keypad displaying

The keypad displaying state of Goodrive100 series inverters is divided into stopping state parameter,

running state parameter, function code parameter editing state and fault alarm state and so on.

4.1.1 Displayed state of stopping parameter

When the inverter is in the stopping state, the keypad will display stopping parameters which is shown in

figure 4-2.

In the stopping state, various kinds of parameters can be displayed. Select the parameters to be displayed

or not by P07.07. See the instructions of P07.07 for the detailed definition of each bit.

In the stopping state, there are 14 stopping parameters can be selected to be displayed or not. They are:

set frequency, bus voltage, input terminals state, output terminals state, PID given, PID feedback, torque set

value, AI1, AI2, AI3, HDI, PLC and the current stage of multi-stage speeds, pulse counting value, length

value. P07.07 can select the parameter to be displayed or not by bit and

》

/SHIFT can shift the parameters

form left to right, QUICK/JOG (P07.02=2) can shift the parameters form right to left.

4.1.2 Displayed state of running parameters

After the inverter receives valid running commands, the inverter will enter into the running state and the

keypad will display the running parameters. RUN/TUNE LED on the keypad is on, while the FWD/REV is

determined by the current running direction which is shown as figure 4-2.

In the running state, there are 24 parameters can be selected to be displayed or not. They are: running

frequency, set frequency, bus voltage, output voltage, output torque, PID given, PID feedback, input

terminals state, output terminals state, torque set value, length value, PLC and the current stage of multi-

stage speeds, pulse counting value, AI1, AI2, AI3, HDI, percentage of motor overload, percentage of

inverter overload, ramp given value, linear speed, AC input current. P07.05 and P07.06 can select the

parameter to be displayed or not by bit and

》

/SHIFT can shift the parameters form left to right,

QUICK/JOG (P07.02=2) can shift the parameters from right to left.

4.1.3 Displayed state of fault

If the inverter detects the fault signal, it will enter into the fault pre-alarm displaying state. The keypad will

display the fault code by flicking. The TRIP LED on the keypad is on, and the fault reset can be operated by

theSTOP/RST on the keypad, control terminals or communication commands.

Содержание Goodrive100 Series

































































































































































































Результаты поиска

Содержание Goodrive100 Series

Отзывы:

Похожие инструкции для Goodrive100 Series

Бренды по названию

Популярные бренды

INVT Goodrive100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Goodrive100 Series

Отзывы:

Похожие инструкции для Goodrive100 Series

Бренды по названию

Популярные бренды