INVT Goodrive100 Series Скачать руководство пользователя страница 14

Страница: 14 / 192

Goodrive100 inverters

Product overview

IKR Aandrijven en Besturen

www.ikr-industries.nl

2.1.4 Installation confirmation

Check as followings after the installation:

1. Check that the load range of the input and output cables meet the need of actual load.

2. Check that the accessories of the inverter are correctly and properly installed. The installation cables

should meet the needs of every component (including reactors, input filters, output reactors, output filters,

DC reactors, braking units and braking resistors).

3. Check that the inverter is installed on non-flammable materials and the calorific accessories (reactors

and brake resistors) are away from flammable materials.

4. Check that all control cables and power cables are run separately and the routation complies with EMC

requirement.

5. Check that all grounding systems are properly grounded according to the requirements of the inverter.

6. Check that the free space during installation is sufficient according to the instructions in user’s manual.

7. Check that the installation conforms to the instructions in user’s manual. The drive must be installed in

an upright position.

8. Check that the external connection terminals are tightly fastened and the torque is appropriate.

9. Check that there are no screws, cables and other conductive items left in the inverter. If not, get them

out.

2.1.5 Basic commissioning

Complete the basic commissioning as followings before actual utilization:

Содержание Goodrive100 Series

































































































































































































Результаты поиска

Содержание Goodrive100 Series

Отзывы:

Похожие инструкции для Goodrive100 Series

Бренды по названию

Популярные бренды

INVT Goodrive100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Goodrive100 Series

Отзывы:

Похожие инструкции для Goodrive100 Series

Бренды по названию

Популярные бренды