INVT Goodrive100 Series Скачать руководство пользователя страница 31

Страница: 31 / 192

Goodrive100 inverters

Installation guidelines

IKR Aandrijven en Besturen

www.ikr-industries.nl

3.2.6 Input /Output signal connection figure

Please use U-shaped contact tag to set NPN mode or PNP mode and the internal or external power supply.

The default setting is NPN internal mode.

Fig 3-7 U-shaped contact tag

If the signal is from NPN transistor, please set the U-shaped contact tag b24V and PW as below

according to the used power supply.

Diagram 3-8 NPN modes

If the signal is from PNP transistor, please set the U-shaped contact tag as below according to the used

power supply.

Diagram 3-9 PNP modes

3.3 Layout protection

3.3.1 Protecting the inverter and input power cable in short-circuit situations

Protect the inverter and input power cable in short circuit situations and against thermal overload.

Arrange the protection according to the following guidelines.

Fig 3-10 Fuse configuration

Note:

Select the fuse as the manual indicated. The fuse will protect the input power cable from damage in

short-circuit situations. It will protect the surrounding devices when the internal of the inverter is short

circuited.

Содержание Goodrive100 Series

































































































































































































Результаты поиска

Содержание Goodrive100 Series

Отзывы:

Похожие инструкции для Goodrive100 Series

Бренды по названию

Популярные бренды

INVT Goodrive100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Goodrive100 Series

Отзывы:

Похожие инструкции для Goodrive100 Series

Бренды по названию

Популярные бренды