INVT Goodrive100 Series Скачать руководство пользователя страница 183

Страница: 183 / 192

Goodrive100 inverters

Appendix C

IKR Aandrijven en Besturen

www.ikr-industries.nl

The inverters below 30kW(including 30kW) only

need braking resistors and the inverters above

37kW(including 37 kW) need braking units

Output filter

Control the interference from the output side of

the inverter and please install close to the output

terminals of the inverter.

Output reactor

Prolong the effective transimiting distance of the

inverter to control the sudden high voltage when

switchiong on/off the IGBT of the inverter.

C.2 Power supply



Check that the voltage degree of the inverter complies with the voltage of the

supply power voltage.

C.3 Cables

C.3.1 Power cables

Dimension the input power and motor cables according to local regulations.

Note:

A separate PE conductor is required if the conductivity of the cable shield is not sufficient for the

purpose.

C.3.2 Control cables

All analog control cables and the cable used for the frequency input must be shielded.

The relay cable needs the cable type with braided metallic screen.

Note: Run analog and digital signals in separate cables.

Check the insulation of the input power cable according to local regulations before connecting to the drive.

Содержание Goodrive100 Series

































































































































































































Результаты поиска

Содержание Goodrive100 Series

Отзывы:

Похожие инструкции для Goodrive100 Series

Бренды по названию

Популярные бренды

INVT Goodrive100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Goodrive100 Series

Отзывы:

Похожие инструкции для Goodrive100 Series

Бренды по названию

Популярные бренды