INVT Goodrive100 Series Скачать руководство пользователя страница 187

Страница: 187 / 192

Goodrive100 inverters

Appendix C

IKR Aandrijven en Besturen

www.ikr-industries.nl

The power of the inverter

Input reactor

Output reactor

GD100-5R5G-4

ACL2-5R5-4

OCL2-5R5-4

GD100-7R5G-4

ACL2-7R5-4

OCL2-7R5-4

GD100-011G-4

ACL2-011-4

OCL2-011-4

GD100-015G/-4

ACL2-015-4

OCL2-015-4

Note:

The rated derate voltage of the input reactor is 2%±15%.

The power factor of the input side is above 90% after adding DC reactor.

The rated derate voltage of the output reactor is 1%±15%.

Above options are external, the customer should indicate when purchasing.

C.6 Filter

Goodrive100 series inverters have embedded C3 filters which can be connected by J10.

The input interference filter can decrease the interference of the inverter to the surrounding equipments.

Output interference filter can decrease the radio noise cause by the cables between the inverter and the

motor and the leakage current of the conducting wires.

Our company configured some filters for the convenient of the users.

The inverter

Input filter

Output filter

Содержание Goodrive100 Series

































































































































































































Результаты поиска

Содержание Goodrive100 Series

Отзывы:

Похожие инструкции для Goodrive100 Series

Бренды по названию

Популярные бренды

INVT Goodrive100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Goodrive100 Series

Отзывы:

Похожие инструкции для Goodrive100 Series

Бренды по названию

Популярные бренды