INVT Goodrive GD300-19-004G-4 Скачать руководство пользователя страница 8

Страница: 8 / 255

Goodrive300-19 series open loop vector inverter special for hosit Safety precautions

-7-



Do not carry the inverter by its cover. The cover may fall off.



Install away from children and other public places.



The inverter cannot meet the requirements of medium and low voltage protection in

IEC61800-5-1 if the sea level of installation site is above 2000m.



Please use the inverter on appropriate condition (See chapter

Installation environment



Do not allow screws, cables or other conductive items to fall inside the inverter.



The leakage current of the inverter may be above 3.5mA during operation. Ground with proper

techniques and ensure the grounding resistor is less than

10Ω. The conductivity of PE

grounding conductor is the same as that of the phase conductor (with the same cross sectional

area).



R, S and T are the input terminals of the power supply, while U, V and W are the output

terminals of the motor. Please connect the input power cables and motor cables with proper

techniques; otherwise the damage to the inverter may occur.

1.4.2 Commissioning and running



Disconnect all power supplies applied to the inverter before the terminal

wiring and wait for at least the designated time on the inverter after

disconnecting the power supply.



High voltage is present inside the inverter during running. Do not carry out

any operation except for the keypad setting.



The inverter may start up by itself when P01.21=1. Do not get close to the

inverter and motor.



The inverter

can not be used as “Emergency-stop device”.



The inverter can not be used to break the motor suddenly. A mechanical

braking device should be provided.

Note:



Do not switch on or off the input power supply of the inverter frequently.



For inverters that have been stored for a long time, check and fix the capacitance and try to run

it again before utilization (see

Maintenance and hardware fault diagnosis



Cover the front board before running, otherwise electric shock may occur.

1.4.3 Maintenance and replacement of components



Only qualified electricians are allowed to perform the maintenance,

inspection, and components replacement of the inverter.



Disconnect all power supplies to the inverter before the terminal wiring. Wait

for at least the time designated on the inverter after disconnection.



Take measures to avoid screws, cables or other conductive items to fall into

Содержание Goodrive GD300-19-004G-4
































































































































































































































































Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Похожие инструкции для Goodrive GD300-19-004G-4

Бренды по названию

Популярные бренды

INVT Goodrive GD300-19-004G-4, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Похожие инструкции для Goodrive GD300-19-004G-4

Бренды по названию

Популярные бренды