INVT Goodrive GD300-19-004G-4 Скачать руководство пользователя страница 42

Страница: 42 / 255

Goodrive300-19 series open loop vector inverter special for hosit Keypad operation procedure

-41-

Fig 5-3 Sketch map of modifying parameters

5.4.2

How to set the password of the inverter

Goodrive300-19 series inverters provide password protection function to users. Set P07.00 to gain

the password and the password protection becomes valid instantly after quitting from the function

code editing state. Press PRG/ESC again to the function code editing state,

“0.0.0.0.0” will be

displayed. Unless using the correct password, the operators cannot enter it.

Set P07.00 to 0 to cancel password protection function.

The password protection becomes effective instantly after retreating from the function code editing

state. Press PRG/ESC again to the function code editing state,

“0.0.0.0.0” will be displayed. Unless

using the correct password, the operators cannot enter it.

Fig 5-4 Sketch map of password setting

5.4.3

How to watch the inverter state through function codes

Goodrive300-19 series inverters provide group P17 as the state inspection group. Users can enter

into P17 directly to watch the state.

Содержание Goodrive GD300-19-004G-4
































































































































































































































































Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Бренды по названию

Популярные бренды

INVT Goodrive GD300-19-004G-4, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Бренды по названию

Популярные бренды