INVT Goodrive GD300-19-004G-4 Скачать руководство пользователя страница 199

Страница: 199 / 255

Goodrive300-19 series open loop vector inverter special for hosit Fault tracking

-198-

8.6.3 Overvoltage

OV fault

Check if the voltage range is in

the standard one or not ?

Check if the ACC/DEC

time is too short

Check if the load

motor is in abnormal

reverse running

Ensure the power supply

meets the need

Check if UVW is short circuited to

the earth and the configuration of

the output side is right or not?

Settle the short circuit

and configure rightly

Shorten the ACC/DEC

time

Check the load and

adjust

If it is the inverter fault,

please contact with our

company

Check if shortening the

ACC/DEC time is allowed

Check if it

needs to use

the options

Add braking options

Adjust the braking

options and the

resistance

Yes

8.6.4 Undervoltage fault

UV fault

Check that if there is

powering off during

the running of the

inverter

If the voltage of the power supply

is in the standard range

Ensure the power supply

meets the need

Check if the air switch and

contactor on the inside is off or

abnormal or not

Switch on the air switch

and contactor and settle

the abnormality

Adjust the power supply

Ensure the power off

reason and settle the

abnormal

If it is the inverter fault,

please contact with our

company

Check if there is big power

device in the same power supply

Yes

Содержание Goodrive GD300-19-004G-4
































































































































































































































































Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Похожие инструкции для Goodrive GD300-19-004G-4

Бренды по названию

Популярные бренды

INVT Goodrive GD300-19-004G-4, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Похожие инструкции для Goodrive GD300-19-004G-4

Бренды по названию

Популярные бренды