INVT Goodrive GD300-19-004G-4 Скачать руководство пользователя страница 83

Страница: 83 / 255

Goodrive300-19 series open loop vector inverter special for hosit Function parameters

-82-

Function

code

Name

Detailed instruction of parameters

Default

value

Modify

make the password protection invalid.

After the set user

’s password becomes valid, if the

password is incorrect, users cannot enter the

parameter menu. Only correct password can make

the user check or modify the parameters. Please

remember all

users’ passwords.

Retreat editing state of the function codes and the

password protection will become valid in a minute. If

the valid password is available, press PRG/ESC to

enter into the editing state of the function codes, and

then

“0.0.0.0.0” will be displayed. Unless input right

password, the operator cannot enter into it.

Note: Restoring to the default value can clear the

password, please use it with caution.

P07.01

Parameter

copy

The function code determines the manner of

parameters copy.

0: No operation

1: Upload the local function parameter to the keypad

2: Download the keypad function parameter to local

address (including the motor parameters)

3: Download the keypad function parameter to local

address (excluding the motor parameter of P02 and

P12 group)

4: Download the keypad function parameters to local

address (only for the motor parameter of P02 and

P12 group)

Note: After completing the 1~4 operations, the

parameter will restore to 0 automatically; the

function of upload and download excludes the

factory parameters of P29.

◎

P07.02

QUICK/JOG

function

selection

0: No function

1: Jogging. Press QUICK/JOG to begin the jogging

running.

◎

Содержание Goodrive GD300-19-004G-4
































































































































































































































































Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Бренды по названию

Популярные бренды

INVT Goodrive GD300-19-004G-4, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Бренды по названию

Популярные бренды