INVT Goodrive GD300-19-004G-4 Скачать руководство пользователя страница 210

Страница: 210 / 255

Goodrive300-19 series open loop vector inverter special for hosit Communication protocol

-209-

higher the baud rate is, the quicker the transmission speed is and the weaker the anti-interference is.

If the twisted pairs of 0.56mm (24AWG) is applied as the communication cables, the Max.

transmission distance is as below:

Baud rate

Max. transmission

distance

Baud rate

Max. transmission

distance

2400BPS

1800m

9600BPS

800m

4800BPS

1200m

19200BPS

600m

It is recommended to use shield cables and make the shield layer as the grounding wires during

RS485 remote communication.

In the cases with less devices and shorter distance, it is recommended to use

120Ω terminal resistor

as the performance will be weakened if the distance increase even though the network can perform

well without load resistor.

10.3.1.1 Single application

Figure 1 is the site Modbus connection figure of single inverter and PC. Generally, the computer does

not have RS485 interface, the RS232 or USB interface of the computer should be converted into

RS485 by converter. Connect the A terminal of RS485 to the 485+ terminal of the inverter and B to the

485- terminal. It is recommended to use the shield twisted pairs. When applying RS232-RS485

converter, if the RS232 interface of the computer is connected to the RS232 interface of the converter,

the wire length should be as short as possible within the length of 15m. It is recommended to connect

the RS232-RS485 converter to the computer directly. If using USB-RS485 converter, the wire should

be as short as possible, too.

Select a right interface to the upper computer (select the interface of RS232-RS485 converter, such

as COM1) after the wiring and set the basic parameters such as communication baud rate and digital

check bit to the same as the inverter.

Содержание Goodrive GD300-19-004G-4
































































































































































































































































Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Бренды по названию

Популярные бренды

INVT Goodrive GD300-19-004G-4, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Бренды по названию

Популярные бренды