INVT Goodrive GD300-19-004G-4 Скачать руководство пользователя страница 207

Страница: 207 / 255

Goodrive300-19 series open loop vector inverter special for hoist Maintenance and hardware diagnosis

-206-

9.4 Capacitors

9.4.1 Capacitors reforming

The DC bus capacitors must be reformed according to the operation instruction if the inverter has

been stored for a long time. The storing time is counted from the delivery date.

Time

Operational principle

Storing time less than 1

year

Operation without charging

Storing time 1-2 years

Connect with the power for 1 hour before first ON command

Storing time 2-3 years

Use voltage-adjusting power supply to charge the inverter

• charging 25% rated voltage for 30 minutes

• charging 50% rated voltage for 30 minutes

• charging 75% rated voltage for 30 minutes

• charging 100% rated voltage for 30 minutes

Storing time more than 3

years

Use voltage-adjusting power supply to charge the inverter

• charging 25% rated voltage for 2 hours

• charging 50% rated voltage for 2 hours

• charging 75% rated voltage for 2 hours

• charging 100% rated voltage for 2 hours

Use voltage-adjusting power supply to charge the inverter:

The right selection of the voltage-adjusting power supply depends on the supply power of the inverter.

The single-phase 220V AC/2A voltage regulator is applied to single/three-phase 220V AC inverter.

The single/three-phase inverter can apply single-phase voltage-adjusting power supply for charging

(L+ to R, N to S or T). All DC bus capacitors can charge at the same time because there is one

rectifier.

High-voltage inverter needs enough voltage (for example, 380V) during charging. The small capacitor

power (2A is enough) can be used because the capacitor nearly does not need current when

charging.

The operation method of inverter charging through resistors (LEDs):

The charging time is at least 60 minutes if charge the DC bus capacitor directly through power supply.

This operation is available on normal temperature and no-load condition and the resistor should be

serially connected in the 3-phase circuits of the power supply.

380V drive device: 1K/100W resistor. LED of 100W can be used when the power voltage is no more

than 380V. But if used, the light may be off or weak during charging.

Содержание Goodrive GD300-19-004G-4
































































































































































































































































Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Бренды по названию

Популярные бренды

INVT Goodrive GD300-19-004G-4, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Бренды по названию

Популярные бренды