INVT Goodrive GD300-19-004G-4 Скачать руководство пользователя страница 20

Страница: 20 / 255

Goodrive300-19 series open loop vector inverter special for hosit Installation guidelines

-19-

Installation guidelines 4

4.1 What this chapter contains

The chapter describes the mechanical installation and electric installation.



Only qualified electricians are allowed to carry out what described in this chapter.

Please operate as the instructions in

Safety precautions

. Ignoring these may

cause physical injury or death or damage to the devices.



Ensure the power supply of the inverter is disconnected during the operation.

Wait for at least the time designated until the POWER indicator is off after the

disconnection if the power supply is applied. It is recommended to use the

multimeter to monitor that the DC bus voltage of the drive is under 36V.



The installation and design of the inverter should comply with the requirement of

the local laws and regulations in the installation site. If the installation infringes

the requirement, our company will exempt from any responsibility. Additionally, if

users do not comply with the suggestions, some damage beyond the assured

maintenance range may occur.

4.2 Mechanical installation

4.2.1 Installation environment

The installation environment is the safeguard for a full performance and long-term stable functions of

the inverter. Check the installation environment as followings:

Environment

Conditions

Installation site

Indoor

Environment

temperature

-10~+50°C

If the ambient temperature of the inverter is above 40°C, derate 1% for

every additional 1°C.

It is not recommended to use the inverter if the ambient temperature is

above 50°C.

In order to improve the reliability of the device, do not use the inverter

if the ambient temperature changes frequently.

Please provide cooling fan or air conditioner to control the internal

ambient temperature below the required one if the inverter is used in a

close space such as in the control cabinet.

When the temperature is too low, if the inverter needs to restart to run

after a long stop, it is necessary to provide an external heating device

Содержание Goodrive GD300-19-004G-4
































































































































































































































































Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Бренды по названию

Популярные бренды

INVT Goodrive GD300-19-004G-4, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Бренды по названию

Популярные бренды