background image

Ver. 3.003  

p91

CONCEPT IQ. PLUS  Programmer’s Manual.

570 to 589

Holidays ................................................................................................ 54

571

Holiday Month ....................................................................................... 55

590 to 595

Daylight Saving .................................................................................... 55

590 to 595

Daylight Saving Programming - Basic ................................................ 22

590 to 595

Daylight Saving Time (DST) Start And End Dates ............................. 55

600

End-of-line Resistor Type .................................................................... 56

600 to 666

Zone Input Programming - Basic                                                       19-20

600 to 666

Zone Input Programming - Basic ........................................................ 23

601 to 616

24 Hour Zone Types ............................................................................ 58

601 to 616

Delayed Zone Type .............................................................................. 57

601 to 616

Duress Zone Type ................................................................................ 58

601 to 616

Fire Zone Type ..................................................................................... 58

601 to 616

Handover Zone Type ........................................................................... 57

601 to 616

Home Zone Types ................................................................................ 57

601 to 616

Instant Zone Type ................................................................................. 57

601 to 616

Key Switch Zone Types ....................................................................... 58

601 to 616

Panic Zone Type .................................................................................. 58

601 to 616

Zone Type ............................................................................................. 57

601 to 616

Zone Input Programming Overview .................................................... 56

651 to 666

Day Alarm Zone Option ....................................................................... 60

651 to 666

Dialer Lockout Zone Option ................................................................. 59

651 to 666

Normally Open (Change Sense) Zone Option ................................... 60

651 to 666

Pulse Count Zone Option .................................................................... 59

651 to 666

Self-Test Zone Option .......................................................................... 60

651 to 666

Silent Zone Option ............................................................................... 59

651 to 666

Siren Lockout Zone Option .................................................................. 59

651 to 666

Zone Options ........................................................................................ 60

701 to 716

Zone Areas ........................................................................................... 60

750 to 769

Timezones ............................................................................................ 61

800 to 810

Auxiliary Event Type ............................................................................. 62

800 to 810

Auxiliary Event Types ........................................................................... 62

800 to 870

Auxiliary Programming Overview ........................................................ 62

801

Strobe Programming - Basic ............................................................... 22

830 to 840

Auxiliary Timer Value ........................................................................... 63

860 to 870

Auxiliary Action ..................................................................................... 63

860 to 870

Auxiliary Actions ................................................................................... 78

890

Auto Isolate on Arming ......................................................................... 64

890

Clock synchronized to 50Hz AC Mains. .............................................. 64

890

Display Zone activity on Terminals. ..................................................... 64

890

Force Arm Areas. ................................................................................. 64

890

General Option Programming - Basic ................................................. 21

890

General Options.  1. ............................................................................. 64

890

Quick Arming ........................................................................................ 64

890

Single Exit Beep in Home Mode. ........................................................ 64

890

Special Siren Tone for System Alarms. ............................................... 64

890

Zone activity on Terminals.  To Display. .............................................. 64

890

Zone Alarm indication after Disarm. .................................................... 64

891

All Area Siren Off control. .................................................................... 65

891

Bell Squawk on Siren for Wireless Remote Key. ............................... 65

891

Call Forwarding. ................................................................................... 65

891

Day Alarms To Activate Terminal Beeper ............................................ 65

891

Delay Siren until Comms complete ..................................................... 65

891

Dialer enabled in Home Mode. ............................................................ 65

891

DTMF Control. ...................................................................................... 65

891

General Options.  2. ............................................................................. 65

891

Multi-Area System. ............................................................................... 65

891

Mutli-Area Option Programming - Basic ............................................. 23

891

Terminal Beeper for Day Alarms. ........................................................ 65

892

6 Digit PIN codes ................................................................................. 66

892

Automatic Battery Testing. ................................................................... 66

892

Battery Test on Arming. ........................................................................ 66

892

Battery Testing -Automatic. .................................................................. 66

892

General Options.  3. ............................................................................. 66

892

Keyswitch Zones Latching. .................................................................. 66

892

Pulse Count Handover. ........................................................................ 66

892

Siren Output To Operate As An Auxiliary ............................................ 66

893

General Options.  4. ............................................................................. 67

897

Fire alarms will activate the Siren. ...................................................... 67

897

Siren.  Emergency Alarms to activate Siren. ...................................... 67

897

Siren.  System Inputs to activate Siren. .............................................. 67

897

System Input Programming - Basic .................................................... 20

897

System Input Siren Enable .................................................................. 67

897 to 898

System Inputs ....................................................................................... 79

897 to 898

System Inputs Overview ...................................................................... 67

898

System Input Dialer Enable ................................................................. 68

899

Duress alarms will activate the Dialer. ................................................ 68

899

Duress Codes operation Enabled. ...................................................... 68

899

Emergency Alarm Programming - Basic ............................................ 20

899

Emergency Options ............................................................................. 68

899

Fire alarms will activate the Dialer. ..................................................... 68

899

Medical alarms will activate the Dialer. ............................................... 68

899

Medical alarms will activate the Siren. ................................................ 68

899

Panic alarms will activate the Dialer. .................................................. 68

899

Panic alarms will activate the Siren. ................................................... 69

Содержание CONCEPT IQ. PLUS































































































Отзывы: