Inner Range CONCEPT IQ. PLUS Скачать руководство пользователя

Страница: 17 / 94

Ver. 3.003

p17

CONCEPT IQ. PLUS Programmer’s Manual.

7. Assign the User Type.

The <A3> Lamp will flash to indicate the system is ready for User Type selection.

The corresponding Zone Lamp (0 to 9) will indicate the User Type selected.

Select the new User Type number

USER TYPE:

Arm only

Can only Arm the system.

Patrol

Can Arm / Can Disarm only after an alarm.

Arm/Dis-arm

Can Arm and Dis-arm the system.

Defer Arm Only

Can only perform Timed Disarm.

User Auxiliary A

Can only Toggle User Auxiliary A On and Off.

User Auxiliary B

Can only Toggle User Auxiliary B On and Off.

Arm/Dis-arm/Isolate Can Arm/Dis-arm the system and Isolate Zones.

Master

Can perform all operations above & Master User
Operations.

Access Only

Can access an Area associated with a disarmed
door

Access without Dis-arm

Can allow access to User who has arm/dis-

arm rights in an Area

3 very short beeps will sound to indicate that the entry is accepted and the new User Type
number will be displayed on the Zone Lamps.

To confirm the selection; Press

3 beeps will sound to confirm the new User Type has been programmed and the system
will automatically advance to the next User number.

8. Add / Change another User or Exit User Programming.

To program or change the next User number simply repeat Steps 3 to 6.

To select another User number to program or change, go back to Step 2.

To exit User Programming; Press

Deleting a User

1. Logon.

Enter your PIN code;

...

2. Select the first User number to be Deleted.

Press

. Where

is the User number (User 02 to User 47).

The <A1> Lamp will flash to indicate the system is ready for the PIN Code or Wireless
Remote Key/Access Card entry.

3. Delete the User.

If a PIN code is already programmed for this User, the corresponding number of Zone
Lamps (4 or 6) will be flashing.

Zone Lamp 1 will Fast flash to prompt for the first digit of the PIN code.

Press

then

Three short beeps will sound to confirm that the PIN code and/or Keyfob/Card data has
been deleted and the User Type set to “0”.

4. Delete another User or Exit User Programming.

To delete the next User number simply repeat Step 3.

To select another User number to delete, go back to Step 2.

To exit User Programming; Press

Содержание CONCEPT IQ. PLUS































































































Результаты поиска

Содержание CONCEPT IQ. PLUS

Отзывы:

Похожие инструкции для CONCEPT IQ. PLUS

Бренды по названию

Популярные бренды

Inner Range CONCEPT IQ. PLUS, Руководство программиста

Результаты поиска

Содержание CONCEPT IQ. PLUS

Отзывы:

Похожие инструкции для CONCEPT IQ. PLUS

Бренды по названию

Популярные бренды