Inner Range CONCEPT IQ. PLUS Скачать руководство пользователя

Страница: 32 / 94

p32

Ver. 3.003 (24/4/03)

CONCEPT IQ. PLUS Programmer’s Manual.

32.

DOOR FORCED

An Installer Code or Master User Code must be used to program this option
Programming the DOOR FORCED system input for DOOR 1, to operate an auxiliary.

This option can require the use of the plug-on auxiliary board

1) Key in your PIN, then Press

, then

then

This assigns event type 131 to Aux 10, when the door reed for DOOR1 goes into alarm without a valid request to

open the door, an output on auxiliary 10 will occur. Cleared with a valid PIN + OFF key.

31.

REX BUTTON ON TERMINAL

An Installer Code or Master User Code must be used to program this option

1) Key in your PIN, then Press

, then

to enable (

to disable ), default is disabled

This option enables the OFF key on the Terminal to act as a REX button

33.

DOOR OPEN TOO LONG (DOTL)

An Installer Code or Master User Code must be used to program this option
Programming the DOTL system input for DOOR 1, to operate an auxiliary.

This option can require the use of the plug-on auxiliary board

1) Key in your PIN, then Press

then

This assigns event type 141 to Aux 9, when the door reed for DOOR1 is open for longer than a period of time

equal to 4 times that of the lock open time set at address 909. Cleared with a valid PIN + OFF key or valid card badge.

No Access Options.

Go to Step 34

“Change Installer PIN”

Содержание CONCEPT IQ. PLUS































































































Результаты поиска

Содержание CONCEPT IQ. PLUS

Отзывы:

Похожие инструкции для CONCEPT IQ. PLUS

Бренды по названию

Популярные бренды

Inner Range CONCEPT IQ. PLUS, Руководство программиста

Результаты поиска

Содержание CONCEPT IQ. PLUS

Отзывы:

Похожие инструкции для CONCEPT IQ. PLUS

Бренды по названию

Популярные бренды