Farm King Model 1050 Скачать руководство пользователя страница 16

Страница: 16 / 174

Safety - 10" Backsaver Auger

FIRE PREVENTION

Maintenance

The machine and some equipment have components

that are at high temperatures under normal operating

conditions. The primary source of high temperatures is

the engine and exhaust system. The electrical system,

if damaged or incorrectly maintained, can be a source

of arcs or sparks.

Flammable debris (leaves, straw, etc.) must be

removed regularly. If flammable debris is allowed to

accumulate, it can cause a fire hazard. Clean often to

avoid this accumulation. Flammable debris in the

engine compartment is a potential fire hazard.

The operator’s area, engine compartment and engine

cooling system must be inspected every day and

cleaned if necessary to prevent fire hazards and

overheating.

All fuels, most lubricants and some coolant mixtures

are flammable. Flammable fluids that are leaking or

spilled onto hot surfaces or onto electrical

components can cause a fire.

Operation

The Farm King machine must be in good operating

condition before use.

Check all of the items listed on the service schedule

under the 8 hour column. (See “SERVICE SCHEDULE”

on page 88.)
Do not use the machine where exhaust, arcs, sparks

or hot components can contact flammable material,

explosive dust or gases.

Starting

Do not use ether or starting fluids on any engine that

has glow plugs. These starting aids can cause

explosion and injure you or bystanders.

Use the procedure in the tractor’s operator’s manual

for connecting the battery and for jump starting.

Electrical

Check all electrical wiring and connections for

damage. Keep the battery terminals clean and tight.

Repair or replace any damaged part or wires that are

loose or frayed.

Battery gas can explode and cause serious injury. Do

not jump start or charge a frozen or damaged battery.

Keep any open flames or sparks away from batteries.

Do not smoke in battery charging area.

Hydraulic System

Check hydraulic tubes, hoses and fittings for damage

and leakage. Never use open flame or bare skin to

check for leaks. Hydraulic tubes and hoses must be

properly routed and have adequate support and secure

clamps. Tighten or replace any parts that show

leakage.

Always clean fluid spills. Do not use gasoline or diesel

fuel for cleaning parts. Use commercial nonflammable

solvents.

Fueling

Stop the engine and let it cool before adding fuel. No

smoking! Do not refuel a machine near open flames or

sparks. Fill the fuel tank outdoors.

Spark Arrester Exhaust System

The spark arrester exhaust system is designed to

control the emission of hot particles from the engine

and exhaust system, but the muffler and the exhaust

gases are still hot.

Check the spark arrester exhaust system regularly to

make sure it is maintained and working properly. Use

the procedure in the machine’s Operator’s Manual for

cleaning the spark arrester muffler (if equipped).

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды