Farm King Model 1050 Скачать руководство пользователя страница 82

Страница: 82 / 174

Operation - 10" Backsaver Auger

Unloading Rear And Side Dump Units

Rear Dump Units

Figure 136

Move the hopper out at a 90° angle from the auger

[Figure 136]

Move the rear dump unit into the unloading position at

the end of the hopper (Item 1) or on the tractor side of

the hopper (Item 2)

[Figure 136]

Position the gate of the rear dump unit over the

hopper (as close to the center of the hopper as

possible).
Stop the rear dump unit and engage the parking brake

(if equipped).

With tractor running at a low idle, engage the tractor

PTO slowly to start the auger. Increase engine RPM

(do not exceed 540 RPM PTO speed).

Slowly open the gate on the rear dump unit.
Adjust gate until the hopper augers and intake auger

can move grain to the main auger without overflowing

the hopper.
When the unit is empty, close the gate, disengage the

PTO and lower engine RPM speed.

Disengage the tractor hydraulics and exit the tractor.

B-0542

•

Do NOT exceed 540 RPM PTO.

•

Keep PTO shields and all guards in place.

•

Keep away from moving parts.

•

Keep bystanders away.

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды