Farm King Model 1050 Скачать руководство пользователя страница 72

Страница: 72 / 174

Operation - 10" Backsaver Auger

Reducing The PTO Driveline Length

Stop the engine and leave the operator’s position.

(See “Leaving The Operator’s Position” on page 66.)
Make sure the PTO driveline and all rotating

components have come to a complete stop before

leaving the operator’s position.

Remove the PTO driveline from the tractor and place

in storage position (if equipped).

Enter the operator’s position. (See “Entering The

Operator’s Position” on page 66.) Start the engine.

Raise or lower the auger to get the shortest distance

between the tractor PTO shaft and auger gearbox PTO

shaft.
Stop the engine and leave the operator’s position.

(See “Leaving The Operator’s Position” on page 66.)
Pull the PTO driveline apart and reinstall each

individual section; one half to the tractor PTO shaft

and one half to the implement gearbox PTO shaft.

Figure 122

1. Hold PTO driveline sections parallel to one another

and measure back 2 in. (50,8 mm) (Item 1) from

the yoke of each section and place mark on

opposite section. Cut the plastic shield at this

length (Item 2)

[Figure 122]

Figure 123

2. Using the plastic guard lengths that were cut off in

[Figure 122]

, align the cut off lengths (Item 1) with

the end of the inner & outer shafts. Place a mark

(Item 2)

[Figure 123]

on the inner & outer shafts

and cut the inner & outer shafts off at this length.

3. Round off all sharp edges and debur.

4. Thoroughly grease and install the PTO driveline

halves together.

5. Recheck for proper operation.

AVOID INJURY OR DEATH

•

Do NOT exceed the rated implement PTO speed.

•

Stay clear of rotating driveline.

•

Keep bystanders away.

•

Keep hands, feet, clothing and long hair away.

•

Keep PTO shields and all guards in place.

•

Disengage PTO, move the tractor controls to the

Neutral position, stop the engine, engage parking

brake and make sure all rotating components are

stopped before leaving the operator’s position.

•

Do NOT service the tractor or implement with the

PTO engaged.

•

Do NOT service the implement in a raised

position unless properly blocked and with all

rotating components stopped.

•

Disengage PTO for road travel.

B-0216

Tractor

PTO Shaft

Auger PTO

Shaft

B-0217

Tractor

PTO Shaft

Auger PTO

Shaft

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды