Farm King Model 1050 Скачать руководство пользователя страница 66

Страница: 66 / 174

Operation - 10" Backsaver Auger

Break - In Checklist

NOTE: The Backsaver Auger must have a break-in

period with different operating conditions than

for normal use.

The tube and flighting must get a polished surface

through use. Once the new auger has polished it will

run smooth at recommended speed.

NOTE: Never operate an empty auger for over one

minute, as the flighting and housing will

experience excessive wear.

During the break-in-period:

1. Run the tractor at slow idle until grain begins to

flow from the discharge. For the first 500 bushels,

operate at the slow speed and restrict the flow of

grain at the intake.

2. Gradually increase the speed until operating at full

PTO speed.

NOTE: Do not run empty during break-in period.

Check the following mechanical items after 1 hour of

operation and again after 10 hours of operation:

1. Check the auger hitch for damaged, loose or

missing parts. Repair as needed before operation.

2. Check for loose fasteners and hardware. Tighten

as required.

3. Make sure that all guards and shields are in place,

secured and functioning as designed

4. Check that the PTO driveline telescopes easily and

turns freely.

5. Check condition of all hydraulic components for

leaks. Tighten fittings to correct leaks or replace

components. Do not operate with hydraulic leaks.

6. Check tire pressure. Inflate per manufacturer’s

specification.

7. Check gearbox oil level. Fill as required. (See

“LUBRICATION” on page 89.)

8. Check the augers. Remove any debris.

AVOID INJURY OR DEATH

•

Disengage the PTO, engage the machine’s parking

brake, stop the engine and make sure all rotating

components are completely stopped before

connecting, disconnecting, adjusting or cleaning

any PTO driven equipment.

•

Always keep PTO shields and all guards in place

when using PTO driven equipment.

•

Disengage PTO for road travel.

•

Keep hands, feet and clothing away.

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды