Farm King Model 1050 Скачать руководство пользователя страница 42

Страница: 42 / 174

Assembly - 10" Backsaver Auger

Figure 51

Place a straight edge (Item 1) along side the three

sprockets. Align sprocket (Item 2)

[Figure 51]

with the

two pre-installed sprockets.

Tighten set screws to secure the sprocket in the set

position.

Figure 52

Install the roller chain (Item 1)

[Figure 52]

as shown.

Figure 53

Install the connecting link (Item 1) through the two

ends of the chain. Install the connecting link plate

(Item 2) onto the connecting link (backside of chain).

NOTE: The spring clip (Item 3) [Figure 53] must be

installed with the closed end facing the

direction the flighting turns.

Install the spring clip (Item 3)

[Figure 53]

onto the

connecting link securing the two ends of the chain

together.

Figure 54

Loosen the three bolts (Item 1) and jam nut (Item 2).

Tighten the adjustment bolt (Item 3)

[Figure 54]

until

there is approximately 1/4” deflection in the chain.

Tighten jam nut and bolts.

B-0644

B-0645

B-0646

B-0647

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Farm King Model 1050, Руководство оператора и каталог запасных частей, Страница: 42 / 174

Результаты поиска

Содержание Model 1050

Отзывы: