Farm King Model 1050 Скачать руководство пользователя страница 38

Страница: 38 / 174

Assembly - 10" Backsaver Auger

Figure 36

Slide the top and center tube sections together until

the mounting flanges contact each other

[Figure 36]

Install the nine 1/2” x 1-1/4” bolts (Item 1)

[Figure 36]

through the tube flanges. Install one 1/2” lock nut on

each bolt.
Lift center tube up until top of rings touch and tighten

top two bolts. Lower center tube and tighten bottom

bolt. Tighten remaining bolts in a criss-cross pattern.
Repeat

[Figure 35]

[Figure 36]

for the bottom tube

section.
Locate and uncoil the four cables.

Cable Sizes

3/8” - Model 1050 & 1060
1/2” - Model 1070

Place one long and one short cable on each side of the

tube assembly (longest cable towards the outside).

Figure 37

Using two 1/2” x 1-1/2” bolts (Item 1) and 1/2” lock

nuts, align and install the 3/8” x 2” x 57-1/4” center

section bridging yoke (Item 2)

[Figure 37]

. Tighten

bolts and lock nuts.

Figure 38

Using two 3/8” x 1-1/4” bolts (Item 1) and 3/8” lock

nuts, align and install the 1/4” x 1” x 25-1/2” center

section bridging tie bar (Item 2)

[Figure 38]

. Tighten

bolts and lock nuts.

B-0612

B-0626

B-0627

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды