Farm King Model 1050 Скачать руководство пользователя страница 55

Страница: 55 / 174

Assembly - 10" Backsaver Auger

Figure 88

Install a ratchet strap (Item 1) onto the bracket (Item

[Figure 88]

on the top of the hopper (connect the

opposite end of the ratchet strap to the mounting

bracket on the top of the intake auger).

Figure 89

Tighten the ratchet strap, align the hopper u-joint

(Item 1) with the shaft (Item 2)

[Figure 89]

on the

intake auger. Tighten the ratchet strap until the u-joint

is all the way on the shaft.

Figure 90

Align the mounting holes on the hopper and intake

auger.

Install one 3/4” x 1-5/8” bolt (Item 1) (from inside)

through the hopper and intake auger. Install one 3/4”

flat washer (Item 2) and 3/4” lock nut (Item 3)

Repeat the

procedure on the opposite side

of the hopper and intake auger.

Tighten the bolt (Item 1)

[Figure 90]

and lock nut

(both sides).

Figure 91

Apply Locktite® to the set screw (Item 1)

[Figure 91]

install and tighten the set screw.

B-0725

B-0730

B-0731

B-0732

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды