Farm King Model 1050 Скачать руководство пользователя страница 97

Страница: 97 / 174

Maintenance - 10" Backsaver Auger

Figure 157

Loosen all cable clamps along the cable being

tightened.

Tighten the nut (Item 1)

[Figure 157]

of the desired

bridging cable on tube.

Tighten both left and right cables evenly.

Tighten the upper bridging cable until the discharge

end of the tube bows up slightly.

Tighten the lower bridging cable to hold the tube in

the slightly raised position.

After tightening the lower and upper cables, check

that the auger tube is straight. No bend right or left.

NOTE: If the nut is fully tightened and bottoms out

against the eye of the adjustment bolt, the

cable will need to be loosened and additional

adjustments will be made on the opposite end

of the cable.

If the nut bottoms out against the eye of the

adjustment bolt, loosen the nut (Item 1)

[Figure 157]

NOTE: Do not remove the nut from the adjustment

bolt.

After adjusting the cable(s), tighten all cable clamps

along the cable(s).

Figure 158

Remove bolt (Item 1)

[Figure 158]

and lock nut (from

mounting bracket on the bottom tube section), move

the yoke (Item 2) back, one hole. Re-install the bolt

and lock nut. Tighten until the yoke is securely

fastened to the tube mount.

Repeat for adjusting remaining bridging cables.

B-0762

B-0653

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды