Farm King Model 1050 Скачать руководство пользователя страница 52

Страница: 52 / 174

Assembly - 10" Backsaver Auger

Figure 80

Install a strap (Item 1)

[Figure 80]

around the intake

auger.
Connect the strap to an approved lifting device.
Raise the intake auger and position over the input box

(Item 2)

[Figure 80]

Figure 81

Lower the intake auger, align the u-joint (Item 1) with

the top gearbox shaft (Item 2)

[Figure 81]

of the input

box.

NOTE: Lubricate top gearbox shaft before lowering

the intake auger onto the shaft.

Lower the intake auger onto the shaft.

Figure 82

Align the hole of intake auger mounting plate (Item 1)

and the hole of intake box mounting plate (Item 2)

[Figure 82]

(both sides).

Install bushing (Item 3)

[Figure 82]

through the intake

auger mounting plate and input box mounting plate

until flush with the inside of the intake auger

mounting plate (both sides).

Figure 83

Install one bolt (Item 1) and lock nut (Item 2)

[Figure

83]

(both sides).

Tighten the bolt and lock nut securely against the

bushing.

B-0462

B-0712

B-0460

B-0461

B-0458

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды