Farm King Model 1050 Скачать руководство пользователя страница 15

Страница: 15 / 174

Safety - 10" Backsaver Auger

SAFETY INSTRUCTIONS (CONT’D)
Safety Rules For Power Take-Off (PTO) Driven

Equipment

•

Keep PTO shields and all guards in place. Replace

damaged or missing shields and guards before

operating.

•

Follow warnings and instructions on machine signs

(decals). Replace damaged or missing decals.

•

Do not wear loose or bulky clothing around the

PTO or other moving parts.

•

Keep bystanders away from PTO driven

equipment, and never allow children near

machines.

•

Read and understand the manuals for the PTO

driven equipment and be aware of safe operating

procedures and hazards that may not be readily

apparent.

•

Always walk around equipment to avoid coming

near a turning PTO driveline. Stepping over, leaning

across or crawling under a turning PTO driveling

can cause entanglement.

•

Position the machine and equipment hitch correctly

to prevent driveline stress and separation.

•

Use caution when turning. Turning too sharp can

cause driveline damage.

•

Use caution when raising PTO driven attachment.

Excessive driveline angle can cause driveline

damage. Use stops if needed.

Machine Requirements And Capabilities

•

Fasten seat belt securely. If equipped with a

foldable Roll-Over Protective Structure (ROPS),

only fasten seat belt when ROPS is up and locked.

DO NOT wear seat belt if ROPS is down.

•

Machine’s three-point hitch must be equipped with

sway bars or chains.

•

Stop the machine and engage the parking brake.

Install blocks in front of and behind the rear tires of

the machine. Install blocks underneath and support

the equipment securely before working under

raised equipment.

•

Keep bystanders clear of moving parts and the

work area. Keep children away.

•

Use increased caution on slopes and near banks

and ditches to prevent overturn.

•

Make certain that the Slow Moving Vehicle (SMV)

emblem is installed so that it is visible and legible.

When transporting the equipment, use the flashing

warning lights (if equipped) and follow all local

regulations.

•

Operate this equipment with a machine equipped

with an approved Roll-Over Protective Structure

(ROPS). Always wear seat belt when the ROPS is

up. Serious injury or death could result from falling

off the machine.

•

Before leaving the operator’s position:

1. Always park on a flat level surface.

2. Place all controls in neutral.

3. Engage the parking brake.

4. Stop engine.

5. Wait for all moving parts to stop.

•

Carry passengers only in designated seating areas.

Never allow riders on the machine or equipment.

Falling off can result in serious injury or death.

•

Start the equipment only when properly seated in

the operator’s seat. Starting a machine in gear can

result in serious injury or death.

•

Operate the machine and equipment from the

operator's position only.

•

The parking brake must be engaged before leaving

the operator’s seat. Rollaway can occur because

the transmission may not prevent machine

movement.

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды