Farm King Model 1050 Скачать руководство пользователя страница 41

Страница: 41 / 174

Assembly - 10" Backsaver Auger

Figure 47

Install the second bearing flange (Item 1)

[Figure 47]

over the drive stub shaft and 1-3/8” bearing. Align the

mounting holes of the two bearing flanges.
Install three 3/8” x 1” Gr. 5 bolts (Item 2)

[Figure 47]

Tighten bolts.

Figure 48

NOTE: Before installing the locking collar, verify the

castle nut is set correctly. Back the castle nut

off just far enough that the cotter pin hole is

covered. Verify that the flighting is pulled all

the way down.

Install the locking collar (Item 1). Using a punch (Item

[Figure 48]

, tap / rotate the locking collar clockwise

to secure in position.

Apply Loctite® to the set screw (Item 3)

[Figure 48]

install and tighten.

Figure 49

Install the 5/16” x 58 mm key (Item 1)

[Figure 49]

Figure 50

Install the sprocket (Item 1)

[Figure 50]

onto the drive

stub shaft (align with key).

B-0639

B-0641

B-0681

B-0643

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды