manualshive.com logo in svg

Farm King Model 1050, Руководство оператора и каталог запасных частей

Поделиться
Скачать
Farm King Model 1050 Скачать руководство пользователя страница 39

37

Assembly - 10" Backsaver Auger

Figure 39

Install a strap (Item 1) on the bottom tube section,

forward of the main bridging yoke mounting brackets

(Item 2) 

[Figure 39]

.

Connect the strap to an approved lifting device.
Raise the bottom tube section until the main bridging

yoke (Item 3) 

[Figure 39]

 can be placed under the

bottom tube section.

Rotate the main bridging yoke

Figure 40

Align the mounting holes of the main bridging yoke

and bottom tube section bridging yoke mounting

brackets 

[Figure 40]

.

Install four 1/2” x 1-3/4” Gr. 5 bolts (Item 1) 

[Figure

40]

, four 1/2” flat washers and 1/2” lock nuts.

Lower the tube assembly to the ground. Remove the

strap.
Tighten the 1/2” bridging bolts and the 3/8” x 1-1/4”

tie bar bolts.

Figure 41

Locate and install the splined shaft (Item 1) into the

bottom tube section flighting, using two 1/2” x 3”

bolts (Item 2) 

[Figure 41]

 and 1/2” lock nuts. Tighten

bolts and lock nuts.

Figure 42

Install a strap (Item 1) around the bottom tube

section, just behind the winch mounting plate (Item 2)

[Figure 42]

.

Connect the strap to an approved lifting device.
Raise the bottom tube section and place a support

(Item 3) 

[Figure 42]

 under the bottom tube section.

Lower the bottom tube section onto the support (leave

strap and lifting device installed).

B-0628

1

2

3

B-0630

1

B-0632

1

2

B-0677

1

2

3

Содержание Model 1050















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды