Farm King Model 1050 Скачать руководство пользователя страница 73

Страница: 73 / 174

Operation - 10" Backsaver Auger

PTO Driveline Engagement Check

Stop the engine and leave the operator’s position.

(See “Leaving The Operator’s Position” on page 66.)
Make sure the PTO driveline and all rotating

components have come to a complete stop before

exiting the tractor.

1. Disconnect the PTO driveline from the tractor and

fully slide the driveline sections together

(retracted).

Figure 124

2. Measure the retracted (compressed) length of the

PTO driveline between the bases of the plastic

guards

[Figure 124]

3. Multiply the retracted driveline length by 1.667 to

determine the PTO driveline Maximum Operating

Length. (i.e.: 25.5 in. (647,7 mm) x 1.667= 42.5

in. (1079,7 mm) Maximum Operating Length).

4. Attach the PTO driveline to the tractor PTO output

shaft.

5. Enter the operator’s position. (See “Entering The

Operator’s Position” on page 66.)

6. With the PTO driveline attached, position the auger

to where the telescoping PTO driveline is at its

maximum operating extension.

7. Stop the engine and leave the operator’s position.

(See “Leaving The Operator’s Position” on

page 66.) Make sure the PTO driveline and all

rotating components have come to a complete stop

before leaving the operator’s position.

Figure 125

8. Measure the length of the PTO driveline between

the bases of the plastic shields

[Figure 125]

determine the maximum operating length.

A. If the measured maximum operating length is

less than the Maximum Operating Length

calculation (from Step 3), the PTO driveline has

adequate engagement

B. If the measured maximum operating length is

equal to or more than the Maximum Operating

Length calculation (from Step 3), the PTO driveline

does not have adequate engagement and should be

replaced with a longer driveline. See your Farm

King dealer for available PTO drivelines.

AVOID INJURY OR DEATH

•

Do NOT exceed the rated implement PTO speed.

•

Stay clear of rotating driveline.

•

Keep bystanders away.

•

Keep hands, feet, clothing and long hair away.

•

Keep PTO shields and all guards in place.

•

Disengage PTO, move the tractor controls to the

Neutral position, stop the engine, engage parking

brake and make sure all rotating components are

stopped before leaving the operator’s position.

•

Do NOT service the tractor or implement with the

PTO engaged.

•

Do NOT service the implement in a raised

position unless properly blocked and with all

rotating components stopped.

•

Disengage PTO for road travel.

B-0218

Tractor

PTO Shaft

Auger PTO

Shaft

Retracted

(Compressed

B-0219

Maximum

Operating Length

Auger PTO

Shaft

Tractor

PTO Shaft

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды