Farm King Model 1050 Скачать руководство пользователя страница 67

Страница: 67 / 174

Operation - 10" Backsaver Auger

Tractor Requirements

Figure 114

The chart

[Figure 114]

lists the hitch weight and total

weight of the 10” Backsaver Auger models. The

tractor / tow vehicle must be rated for listed weight to

transport the specified auger model.

Figure 115

The chart

[Figure 115]

lists the minimum tractor PTO

hp (with 540 rpm PTO) and approximate hydraulic

pressure for lift.
The 10” Backsaver Auger will require a tractor, three

auxiliary hydraulic functions, Category IV rated

drawbar.

The tractor must be equipped with a 6 - spline, 1-3/8

inch PTO shaft when used with the 10” Backsaver

Auger.

Drawbar Adjustment

Figure 116

Adjust the tractor’s drawbar in / out, until the center

of the hitch pin hole (Item 1)

[Figure 116]

is 16 inches

(410 mm) from the end of the tractor’s PTO shaft.

See your tractor’s owner’s manual for correct

adjustment procedures.

NOTE: A tractor hitch of less than 16” minimum will

result in PTO bottoming out, when operating

auger at maximum height.

Figure 117

The distance between the tractor and the auger PTO

shaft should be between 36 - 38 in. (914 - 965 mm)

with the tractor and auger on level ground and the

auger in full down position. This distance is obtained

AUGER

MODEL

HITCH WEIGHT

TOTAL WEIGHT

1050

770 lb (349 kg)

2545 lb (1155 kg)

1060

840 lb (381 kg)

2987 lb (1356 kg)

1070

840 lb (381 kg)

3354 lb (1523 kg)

1080

660 lb (299 kg)

3622 lb (1644 kg)

AUGER

MODEL

MINIMUM PTO HP

(with 540 RPM PTO)

HYD PSI FOR LIFT

(approximate)

1050

40 hp

1000 psi

1060

48 hp

1000 psi

1070

55 hp

1000 psi

1080

65 hp

1000 psi

•

Do NOT exceed 540 RPM PTO.

•

Keep PTO shields and all guards in place.

•

Keep away from moving parts.

•

Keep bystanders away.

B-0001

16 in.

(410 mm)

B-0528

36 - 38 in.

(914 - 965 mm)

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды