Farm King Model 1050 Скачать руководство пользователя страница 58

Страница: 58 / 174

Assembly - 10" Backsaver Auger

bracket. Install one 7/16” flat washer and 3/8” lock

nut on the three bolts. Tighten bolts and nuts.

Figure 100

Align the handle (Item 1)

[Figure 100]

with the input

shaft.

Install the nut (Item 2)

[Figure 100]

. Tighten the nut

against the handle and torque to 22 - 25 ft.-lb. (30 -

34 N•m).

Figure 101

Locate the winch cable. Install the open end of the

cable (Item 1)

[Figure 101]

over the pulley on the top

of the lift boom.

Figure 102

Feed the open end of the cable (Item 1)

[Figure 102]

through the slot(s) and around the lower pulley on the

bottom of the lift boom.

Route the cable to the hand winch.

B-0719

•

Do not over torque the nut against the handle.

•

Do not adjust the double lock nuts on the long

end of the input shaft.

B-0741

B-0742

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды