Farm King Model 1050 Скачать руководство пользователя страница 9

Страница: 9 / 174

Introduction - 10" Backsaver Auger

OWNER’S INFORMATION

Thank you for your decision to purchase a Farm King

Backsaver Auger. To ensure maximum performance of

your equipment, it is mandatory that you thoroughly

study the Operator And Parts Manual and follow the

recommendations. Proper operation and maintenance

are essential to maximize equipment life and prevent

personal injury.
Operate and maintain this equipment in a safe manner

and in accordance with all applicable local, state, and

federal codes, regulations and / or laws. Follow all on-

product labeling and instructions.
Make sure that all personnel have read this Operator

And Parts Manual and thoroughly understand safe and

correct operating, installation and maintenance

procedures.
Farm King is continually working to improve its

products. Farm King reserves the right to make any

improvements or changes as deemed practical and

possible without incurring any responsibility or

obligation to make any changes or additions to

equipment sold previously.
Although great care has been taken to ensure the

accuracy of this publication, Farm King makes no

warranty or guarantee of any kind, written or

expressed, implied or otherwise with regard to the

information contained within this manual. Farm King

assumes no responsibility for any errors that may

appear in this manual and shall not be liable under any

circumstances for incidental, consequential or punitive

damages in connection with, or arising from the use of

this manual.
Keep this manual available for frequent reference. All

new operators or owners must review the manual

before using the equipment and annually thereafter.

Contact your Farm King Dealer if you need assistance,

information, or additional copies of the manual. Visit

our website at

www.farm-king.com

for a complete list

of dealers in your area.

The directions left, right, front and rear, as mentioned

throughout this manual, are as viewed from the rear

of the equipment.

Serial Number Location

Please enter the model and serial number in the space

provided for easy reference.

Figure 1

The serial number plate (Item 1)

[Figure 1]

is located

on the input box end of the bottom tube assembly.

Always use your serial number when requesting

information or when ordering parts.

Manual Storage

Figure 2

The Operator And Parts Manual and other documents

can be stored in the canister (Item 1)

[Figure 2]

located on side of the input box.

LEFT

RIGHT

FRONT

REAR

B-0636

Model Number:

Serial Number:

B-0720

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды