Farm King Model 1050 Скачать руководство пользователя страница 51

Страница: 51 / 174

Assembly - 10" Backsaver Auger

Figure 77

Install the intake spacer (Item 1)

[Figure 77]

on the

top of the input box.

Figure 78

Install one 1/4” x 13/32” ID x 1-1/4” OD washer (Item

1) in the four corners of the intake spacer (Item 2)

[Figure 78]

Figure 79

Install the input box pivot (Item 1) inside the four 1/4”

x 13/32” ID x 1-1/4” OD washers. Align the mounting

holes and install one input box ring clamp (Item 2) and

one 3/8” x 1-1/2” bolt (Item 3)

[Figure 79]

at the four

corners of the intake spacer.
Tighten bolts to secure the input box pivot to the

input box.

NOTE: The input box pivot should rotate freely.

Install the plastic sleeve (Item 4) onto the input box

pivot. Install one clamp (Item 5)

[Figure 79]

and

tighten to secure the plastic sleeve to the intake auger

B-0708

B-0766

B-0715

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды