Farm King Model 1050 Скачать руководство пользователя страница 96

Страница: 96 / 174

Maintenance - 10" Backsaver Auger

BRIDGING CABLES

Cable Inspection

Regularly check the tightness of all cable clamps to

avoid slipping. Inspect cables regularly for damage,

wear or corrosion.

Cable inspections should be done at the beginning of

operation and directly after the auger has been towed

or transported.

Use a piece of cloth or rag to slide across the cables

to locate broken or frayed wires. Replace cables as

needed.

Lubricating

To prevent damage by corrosion, the cables should be

kept well lubricated.

Cleaning

Periodic cleaning of cables by using a stiff brush and

kerosene or with compressed air or live steam and re-

lubricating will help to lengthen cable life and reduce

abrasion and wear on sheaves and drums.

Lower And Upper Bridging Cables

Figure 156

Install a strap (Item 1)

[Figure 156]

around the tube.

Connect the strap to an approved lifting device.
Raise the lifting device, until tight, to support the

auger tube(s).

Always wear the proper hand and eye protection

when serving the equipment.

AVOID INJURY OR DEATH

Before servicing bridging cables:
•

Always park on a flat level surface.

•

Fully lower the main auger into the transport

position.

•

Disconnect the PTO driveline.

•

Support the main auger tube with an approved

lifting device.

•

Chock tires.

Completely unload auger before adjusting bridging

cables.

B-0608

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды