manualshive.com logo in svg

Farm King Model 1050, Руководство оператора и каталог запасных частей

Поделиться
Скачать
Farm King Model 1050 Скачать руководство пользователя страница 31

29

Assembly - 10" Backsaver Auger

Figure 13

Locate and install the lift arm cradle (Item 1) 

[Figure

13]

 onto the bottom of LH & RH undercarriage arm

mounting brackets.

Install one 1/2” flat washer on two 1/2” x 1-1/4”

bolts. Install the two bolts (Item 2) 

[Figure 13]

 with

flat washers down from the top, then install one 1/2”

lock nut onto each bolt. Do not tighten at this time.

Figure 14

Install a strap (Item 1) around the RH lower lift arm

(Item 2) 

[Figure 14]

.

Connect the strap to an approved lifting device.
Raise and move the lower lift arm to the assembly

area.

Figure 15

Align and lower the lower lift arm (Item 1) down onto

the top mounting bracket (Item 2) 

[Figure 15]

 on the

RH undercarriage arch.

Clevis Pin Sizes

1” x 2-13/16” - 1050 & 1060 Models
1-1/4” x 2-13/16” - 1070 Models

Install one clevis pin (Item 3) 

[Figure 15]

 through the

lower lift arm and undercarriage arch. Install one 1”

I.D. flat washer onto the lift arm clevis pin.

Cotter Pin Sizes

3/16” x 1-1/2” - 1050 & 1060 Models
1/4” x 2” - 1050 & 1060 Models

Install one cotter pin (Item 4) 

[Figure 15]

 into the lift

arm clevis pin.

Install the LH lower lift arm.

B-0598

1

2

2

B-0599

1

2

B-0600

1

3

4

2

Содержание Model 1050















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды