Farm King Model 1050 Скачать руководство пользователя страница 70

Страница: 70 / 174

Operation - 10" Backsaver Auger

Connecting The PTO Driveline

NOTE: Clean and grease tractor’s PTO shaft and PTO

driveline coupling each time driveline is

connected.

Stop the engine and leave the operator’s position.

(See “Leaving The Operator’s Position” on page 66.)

Remove the PTO driveline from the storage position (if

applicable).

Figure 120

Retract the collar and slide the PTO driveline (Item 1)

onto the tractor PTO shaft until it locks onto the shaft.

Push and pull on the PTO driveline to verify it is

securely attached to the PTO shaft. Install PTO

driveline safety chain (Item 2)

[Figure 120]

NOTE: The PTO driveline must have a means to retain

it to the PTO shaft on the tractor.

AVOID INJURY OR DEATH

Warnings on the machine and in the manuals are for

your safety. Failure to obey warnings can cause

serious injury or death.

Improper hitch installation can cause PTO driveline

damage.

•

Do not modify the hitch or use an unapproved

hitch.

•

Make sure the PTO driveline is of adequate length

and that u-joints are in the correct phase.

B-0113

B-0112

•

Do NOT exceed 540 RPM PTO.

•

Keep PTO shields and all guards in place.

•

Keep away from moving parts.

•

Keep bystanders away.

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды