Farm King Model 1050 Скачать руководство пользователя страница 89

Страница: 89 / 174

Maintenance - 10" Backsaver Auger

TROUBLESHOOTING

Chart

NOTE: If a problem is encountered that is difficult to solve, even after having read through this troubleshooting

section, please call your local distributor, dealer or factory. Before you call, please have this Operator And

Parts Manual and the serial number of your machine at hand.

PROBLEM

CAUSE

CORRECTION

Cannot start augers.

Plugged auger or obstruction.

Shutoff tractor and disconnect the

PTO. Remove obstruction.

Bearing failure.

Check bearings and replace if

required.

Grain flow is too fast.

Discharge gate(s) open too far.

Close the gate(s) to allow a slower

grain flow to the hopper / intake

auger.

Grain flow is too slow.

Discharge gate(s) not open enough. Open the gate(s) to allow a faster

grain flow to the hopper intake auger.

Tractor RPM set too low.

Raise tractor RPM to proper setting.

Excessive auger vibration.

Flighting and/or tube are damaged.

Replace flighting and / or tube.

Running auger empty.

Replace flighting and / or tube.

Bent auger flighting.

Remove flighting and inspect for

straightness. If a bend is detected,

straighten the flight and re-install.

Improper PTO speed.

Adjust PTO speed.

Plugging the auger.

Improper PTO speed.

Adjust PTO speed.

Overloading hopper and / or auger.

Reduce the rate of flow into the

intake hopper.

Foreign objects in the auger.

Disconnect PTO driveline and remove

foreign objects.

Wet grain.

Reduce the rate of flow into the

intake hopper.

Snow or ice in grain.

Reduce the rate of flow into the

intake hopper.

Instructions are necessary before operating or servicing equipment. Read and understand the Operator

And Parts Manual and safety signs (decals) on equipment. Follow warnings and instructions in the

manuals when making repairs, adjustments or servicing. Check for correct function after adjustments,

repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды