Farm King Model 1050 Скачать руководство пользователя страница 86

Страница: 86 / 174

Operation - 10" Backsaver Auger

adequate space for the auger to be lowered into the

transport position.
Stop the tractor and engage the parking brake.

Figure 141

Fully lower the auger until the upper lift arm (Item 1)

contacts the cradle rest (Item 2)

[Figure 141]

(both

sides).

Engage the tractor’s parking brake, stop the engine

and exit the tractor.

Figure 142

Remove the PTO driveline safety chain (Item 1).

Retract the collar (Item 2)

[Figure 142]

and slide the

PTO driveline off the tractor PTO shaft.

Figure 143

Place the PTO holder chain (Item 1)

[Figure 143]

around the PTO driveline.

Fully raise the jack (Item 2)

[Figure 143]

and rotate

into the transport position (horizontal).

Verify that the auger is securely fastened to the

tractor / tow vehicle and that the hitch safety chain is

properly attached to the auger and tractor / tow

vehicle.

Verify that the SMV (Slow Moving Vehicle) sign is

attached and visible.

Verify that the amber lights are clean and operating

correctly.

Always lower the auger before transporting and allow

the weight of the auger to rest on the undercarriage

and not the hydraulic cylinders.

B-0671

AVOID INJURY OR DEATH

Before you leave the operator’s position:

•

Always park on a flat level surface.

•

Place all controls in NEUTRAL.

•

Engage the park brake.

•

Stop the engine and remove the key.

•

Wait for all moving parts to stop.

B-0113

B-0112

B-0767

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды