Farm King Model 1050 Скачать руководство пользователя страница 61

Страница: 61 / 174

Assembly - 10" Backsaver Auger

Backsaver Auger 1070 Flow Control Assembly

Figure 107

Locate one each of the following components:
1. 08 MNPT x 08 FNPT 45° Elbow

2. 08 MNPT x 08 MNPT Straight Adaptor

3. 08 MORB x 08 SWFNPT 45° Elbow

4. 08 FNPT One Way Flow Control Valve

5. 08 x 010 MJIC x 08 MNPT Hydraulic Hose

NOTE: Apply teflon tape to the male threads of each

fitting.

Install the 08 MNPT x 08 FNPT 45° elbow into the

flow control valve

[Figure 107]

Install the 08 MNPT x 08 MNPT straight adaptor into

the flow control valve

[Figure 107]

Install the 08 MORB x 08 SWFNPT 45° elbow onto

the close nipple

[Figure 107]

Install the 08 x 010 MJIC x 08 MNPT hydraulic hose

into the 08 MNPT x 08 FNPT 45° elbow

[Figure 107]

NOTE: Place a collection container under the hydraulic

cylinder ports before removing the plugs.

Figure 108

NOTE: Model 1070 Backsaver Auger Flow Control

Assembly shown above [Figure 108].

Remove the plastic plug from the base end (upper) of

the hydraulic cylinder.

Install the flow control valve assembly (Item 1)

[Figure

108]

into the hydraulic cylinder.

Tighten all connections.

Figure 109

Remove the plastic plug from the rod end (lower) of

the hydraulic cylinder.
Locate and install the 08 MORB vent plug (Item 1)

[Figure 109]

into the hydraulic cylinder.

B-0694

B-0695

B-0697

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды